Above ground swimming pool

A swimming pool in your garden is much easier to install than you might expect. A new above ground pool is both reasonably priced and easy to repair. Unlike inflatable pools that often are not very hygienic, but also as a loss, which are much stronger and have all the advantages of a fixed pool without the need for a building permit. They cost a fraction of the price.

Obviously your new above ground pool will bewith instructions to follow, but here is a brief summary of the steps to follow.

Where
Dry assemble the base of the timber in-situ, so that any problems of access and whether the construction of new roads or services necessary for switching.

Excavation
Even if the pool is completely off the ground, you will still need to remove the soil for the base. Draw a rectangular space of at least 60 cmlarger than the pool and remove all the topsoil (15 cm).

Concrete base
You'll find it easier if you do it in two stages. First was a thin (5cm) layer of blinding concrete over the entire excavated surface - this gives you a clean, flat floor to work on. Subsequently, the position of the steel poles that the "ribs" of the sacrifice of pool. "Place 5 inches above the strong blinding concrete reinforcing mesh and, if the soil is poor, another layer5 cm mesh over the upper surface of the concrete. Pour in at least 15 centimeters and perhaps the most 30cm of structural quality concrete mix stir all the air supplied.

Timber superstructure
When the concrete has hardened (about 2 days), start the installation of the wooden frame, making sure to follow the manufacturer's instructions with respect to the joint.

Piping - Phase 1
Install the skimmer unit and cut holes inwall of the timber frame to accommodate the unloading of the pump intake and any lighting. Use a hole saw good and be careful not too big a hole.

Sub-Liner
Carefully brush the floor and vacuum the pool, since any debris left behind is a potential flaw in your pocket. If the floor is clean, spray with glue and cut and mount the sub-liner. This provides a cushioning effect on the floor and walls and also protects the lining Mainfrom damage.

Piping - Phase 2
Install gaskets and frames for the pump inlet, exhaust and lights cut through the sub-liner, which is necessary to expose these holes. Be careful not to over cut.

Main Liner
Exposed to the sun for an hour before coating in order to warm up and smooth them. Starting from one corner of the wooden structure, the cover shot of the pool wall and smooth as you gently stretchso. View the most recent 10 cm, insert a tube from a powerful vacuum cleaner and seal. Draw as much air as possible between the coating and the sub-liner. Anyone who uses the pool goes from here to do with socks or bare feet.

Piping - Phase 3
Fill the pool to a depth of about 15 cm to the liner in its final position to stretch. Use a vacuum cleaner for the last time, remove and seal the top end of the line. Log inpool and install the finals of the pump intake, exhaust and make sure that the electric lights of the last free the storm.

Electrical work
Need an electrician for a switch for you to design and supply. It 's a good idea if you put in a timer and an additional link (you may need to invest in an automatic cleaner). They may also tie in the light - you might want to have arranged for an additional pushthis.

Piping - Phase 4
Carefully assemble the filter pump and fill it with clean, fine sand. Install all in-flow and flow lines to the pump and carefully to ensure that joints are watertight. Fill the pool until the middle of the skimmer unit. First works pump backwash pump and set the timer.

Chemical dosing
Using a pH and chlorine test kit (available at any retailer of swimming pool accessories), or acidalkali to bring your pool to a pH of 7.4 and typically a chlorine level of about 3 ppm. Add algaecide once a week and test, if necessary, and fill, water, acid or alkali and chlorine at the same time. If you use solar rings, save the evaporation of water and chemicals as well as extend your swimming season.

Access
Fit and stairs if necessary.

Maintenance
Drain the water at a low level andCover the winter, using the pump from time to time to avoid standing water. Treating with teak oil every year to keep it free of rot and handsome.

Now you are ready for your above ground pool to enjoy.

Tags : Forced Air Heaters Buy Cheap Duvet Covers | LOWER Prices Air Condition Store